Proses Upgrade Komunikasi Distributed Control System dari Remote Input/Output ke Network Input/Output

Fitria Hidayanti; Fitri Rahmah; Dimas Sigit Priyatna; Ardiyanti Aulia

doi:10.30998/string.v6i3.10431

Proses Upgrade Komunikasi Distributed Control System dari Remote Input/Output ke Network Input/Output

Fitria Hidayanti^(1*), Fitri Rahmah⁽²⁾, Dimas Sigit Priyatna⁽³⁾, Ardiyanti Aulia⁽⁴⁾

(1) Universitas Nasional
(2) Universitas Nasional
(3) Universitas Nasional
(4) PT Yokogawa Indonesia
(*) Corresponding Author

Abstract

The use of control systems for industrial automation is currently achieving rapid movements, one of which is the Distributed Control System (DCS). DCS has several generations in terms of software and hardware. This research discusses DCS upgrades in terms of hardware. Upgrading DCS from Remote Input/Output (R I/O) to Network Input/Output (N I/O) has two stages, upgrade software and hardware upgrading run simultaneously. CS 3000 is still integrated with Windows 7, which is software from R I/O, while to keep up with the development of Windows technology, 10 R I/O cannot reach it. For N I/O itself, it uses Centum VP software that is integrated with Windows 10. R I/O is limited to using RJ45 cable, which has a range of tens of meters, so it must use a repeater to connect long-distance communication. While, in communication between Marshalling Cabinets with field instruments, fibre optics can reach 5 km, save costs, transfer data faster, and only need one connecting cable.

Keywords

Distributed Control System; Remote I/O,; Network I/O

Full Text:

PDF

References

R. V. Barenji, A. V. Barenji, and M. Hashemipour, “A multi-agent RFID-enabled distributed control system for a flexible manufacturing shop,” International Journal of Advanced Manufacturing Technology, vol. 71, no. 9–12, 2014, doi: 10.1007/s00170-013-5597-2.

R. Anand, “DCS, PLC and open control systems - History, issues and selection,” in ISA TECH/EXPO Technology Update Conference Proceedings, 2001, vol. 413 I.

A. M. Damayanti, M. Rifa’i, and T. Tarmukan, “Implementasi Sistem Kontrol PID pada Proses Reverse Osmosis Pengolahan Air Laut Berbasis DCS,” Jurnal Elektronika dan Otomasi Industri, vol. 3, no. 2, 2020, doi: 10.33795/elkolind.v3i2.74.

C. Dey and S. K. Sen, Industrial Automation Technologies. 2020. doi: 10.1201/9780429299346.

F. Putra, M. Kamal, and N. Safitri, “Modifikasi Sistem Pengendalian Proses Back Wash Berdasarkan Sensor PDT pada Sirkulasi Cooling Water Berbasis DCS di PT. Pupuk Iskanda Muda,” Jurnal TEKTRO, vol. 3, no. 1, 2019.

H. S. N. Muzwar, A. K. Pamososuryo, and E. Ekawati, “Pemodelan Kolom Distilasi Pabrik Petrokimia dengan Menggunakan Distributed Control System,” Jurnal Otomasi Kontrol dan Instrumentasi, vol. 6, no. 2, 2015, doi: 10.5614/joki.2014.6.2.2.

M. Saravanabalaji and V. Athappan, “Level Plant Automation Using Yokogawa DCS Centum-VP - A Case Study,” in Lecture Notes on Data Engineering and Communications Technologies, vol. 26, 2019. doi: 10.1007/978-3-030-03146-6_95.

K. (Universitas B. Ramadhan, “Sistem Kontrol Multivariabel Temperatur dan Level dengan Yokogawa DCS CENTUM VP,” Journal of Chemical Information and Modeling, vol. 110, no. 9, 2017.

Y. Irwanto, D. Harsono, and Sutanto, “Automation of mixing tank system in STTN-BATAN mini plant using DCS Centum VP,” Journal of Physics: Conference Series, vol. 1436, no. 1, 2020, doi: 10.1088/1742-6596/1436/1/012128.

DOI: http://dx.doi.org/10.30998/string.v6i3.10431