Studi Kasus Terhadap Alat Penukar Kalor 127-C PUSRI IV Berbasis Simulasi Program Heat Transfer Research Inc. (HTRI) Dengan Variabel Jumlah Plug dan Material Tube

Nucke Aurelia; Lia Cundari; Winandyo Mangkoto

doi:10.30998/faktorexacta.v15i4.14148

Studi Kasus Terhadap Alat Penukar Kalor 127-C PUSRI IV Berbasis Simulasi Program Heat Transfer Research Inc. (HTRI) Dengan Variabel Jumlah Plug dan Material Tube

Nucke Aurelia⁽¹⁾, Lia Cundari^(2*), Winandyo Mangkoto⁽³⁾

(1) Universitas Sriwijaya
(2) Universitas Sriwijaya
(3) PT. Pupuk Sriwidjaja (PUSRI)
(*) Corresponding Author

Abstract

Heat exchanger (HE) is used as a medium for heat exchange between fluids. One of the most critical HE at PUSRI, is the 127-C (Ammonia Refrigerant Condenser) in the PUSRI-IV ammonia unit which is supported by 2 identical HEs, namely 127-CA and 127-CB. This HE serves to condense ammonia gas into liquid ammonia. After evaluating the performance of this HE, there was an average decrease of 31.46%. Therefore, it is necessary to optimize this HE, one of which is through research using the HTRI (Heat Transfer Research Inc.) simulator to see the effect of the number of plugs and tube material replacement. The variable number of plugs used are 17, 250, 500, 750 and 1000 for the 127-CA and 21, 250, 500, 750 and 1000 for the 127-CB. As for the tube material variables, namely Carbon Steel (CS), 304- Stainless Steel (304-SS), and 316- Stainless Steel (316-SS). After simulation and analysis were carried out by considering the factors of heat transfer performance, corrosion resistance and cost-benefit, it was concluded that re-tubing with 304-SS material was the most appropriate choice. The maximum number of plugs for CS material is 1000 pieces while for 304-SS and 316-SS materials it is 750 pieces.

Full Text:

PDF

References

A. Adhitiya and D. Ichsani, "Simulasi Performansi Heat Exchanger Type Shell And Tube Dengan Double Segmental Baffle Terhadap Helical Baffle," Jurnal Teknik POMITS, vol. 2, no. 3, pp. 419-424, 2013.

S. Adumene, T. Nwaoha and G. P. Ombor, "Design and Off-Design Performance Evaluation of Heat Exchanger in an Offshore Process Configuration," Open Access Library Journal Scientific Research, vol. 3, no. 6, pp. 1-9, 2016.

F. R. P. Arrieta, J. D. S. Santos and W. H. Saldanha, "Calculation of the Heat Transfer Surface Area of Heat Exchangers for Waste Heat Recovery with the Kaline Cycle," International Journal of Advanced Engineering Research and Science (IJAERS), vol. 5, no. 11, pp. 13-16, 2018.

B. Baehr, H. Dieter and S. Karl, Heat and Mass Transfer Edisi 3, Verlag Berlin Heidelberg: Springer, 2011.

M. Bailyn, A Survey of Thermodynamics, New York: American Institute of Physics, 1994.

T. L. Bergman, A. S. Lavine, F. P. Incropera and D. P. DeWitt, Fundamentals of Heat and Mass Transfer, New York: John Wiley & Sons, 2017.

I. Bizzy and R. Setiadi, "Studi Perhitungan Alat penukar Kalor Tipe Shell And Tube dengan Program heat Transfer Research Inc (HTRI)," Jurnal Rekayasa Mesin, vol. 13, no. 1, pp. 67-77, 2013.

D. Bhatt and P. M. Javhar, "Shell and Tube Heat Exchanger Performance Analysis," International Journal of Science and Research (IJSR), vol. 3, no. 9, pp. 1872-1881, 2014.

B. C. I. T. J. S. C. Black Cat Insulation Technical Joint Stock Company (BlackCatJSC), "The Difference Between 304 And 316 Stainless Steel," 2020. [Online]. Available: https://blackcatjsc.com.vn/-en/ss304-vs-ss316/#:~:text=304%20vs%2031-6-%20stainless%20steel%20cost%3A%20Tak-ing%20steel%20plates%20as,Ni%2C%20Cr%20and%20Mo. [Accessed 14 Oktober 2021].

J. R. Davis, ASM Specialty Handbook Stainless Steels, Netherlands: ASM International, 1995.

U. Effiong and R. L. Neitzel, "Assessing the direct occupational and public health impacts of solar radiation management with stratospheric aerosols," Environmental Health, vol. 15, no. 7, pp. 1-9, 2016.

G. Elert, The physics hypertextbook, New York: Glenn Elert, 1998.

G. H. Farrahi, M. Chamani, A. Kiyoumarsioskouei and A. H. Mahmoudi, "The effect of plugging of tubes on failure of shell and tube heat exchanger.," Engineering Failure Analysis, vol. 104, no. 1, p. 545–559, 2019.

C. H. Forsberg, Heat Transfer Principles and Applications Edisi 1, Cambridge, Massachusetts.: Academic Press, 2020.

R. Handibag, D. U. Potdar and A. Jadhav, "Thermal Design of Tube and Shell Heat Exchanger and Verification by HTRI Software," International Journal of Engineering Research & Technology (IJERT), vol. 9, no. 12, pp. 525-530, 2020.

H. Heat Exchange Institute (HEI), Standards for Closed Feedwater Heaters Edisi 9, Ohio: Heat Exchange Institute (HEI), 2015.

H. T. R. I. Heat Transfer Rearch Inc.(HTRI), Design Manual, Texas: Heat Transfer Rearch Inc. (HTRI), 2006.

J. Holman, Heat Transfer (Mcgraw-hill Series in Mechanical Engineering) Edisi 10, New York: McGraw-Hill Education, 2009.

M. Jacob, Heat Transfer, New York: Wiley, 1958.

R. Karwa, Heat and Mass Transfer Edisi 2, New York: Springer, 2020.

D. Q. Kern, Process Heat Transfer, New York: McGraw-Hill International Book Company Inc, 1950.

R. T. Loto, "Study of the Corrosion Resistance of Type 304L and 316 Austenitic Stainless Steels in Acid Chloride Solution," Oriental Journal of Chemistry, vol. 33, no. 3, pp. 1090-1096, 2017.

M. Masrufaiyah and T. J. Sulistiono, "Analisa Pengaruh Jumlah Plug pada Kondenser Terhadap Efisiensi dan Heat Transfer yang Hilang di PLTU Unit 3 dan 4 PT. PJB UP. Gresik," Jurnal Keilmuan dan Terapan Teknik, vol. 7, no. 1, pp. 1-15, 2018.

A. Moskvitin, "Heat exchanger, tube bundle," 2020. [Online]. Available: https://www.shutterstock.com/image-photo/-heat-exchanger-tube-bundle-7-93873270. [Accessed 5 Oktober 2021].

R. K. Panda and B. Prasad, "Effect of Thermal Conductivity on Heat Transfer From a Flat Plate With Combined Impingement and Film Cooling," in Proceedings of the ASME 2012 Gas Turbine India Conference, Mumbai, Maharashtra, India, 2012.

R. Poškas, A. Sirvydas, V. Kulkovas and P. Poškas, " An Experimental Investigation of Water Vapor Condensation from Biofuel Flue Gas in a Model of Condenser, (1) Base Case: Local Heat Transfer without Water Injection," Processes, vol. 9, no. 844, pp. 1-15, 2021.

P. Prayudi, R. A. Diantari and S. D. Susilo, "Analisa Pengaruh Plugging Evaporator Terhadap Performance Desalination Plant Unit 2 PLTGU Gresik," Jurnal Power Plant, vol. 1, no. 1, pp. 38-41, 2015.

Y. S. Rajput and A. Arya, "CFD Analysis of Cross Flow Heat Exchanger with Different Fin Thickness," Materials Science, vol. 1, no. 1, pp. 1-20, 2019.

D. D. Rana, "Waste process steam heat recovery system," International Journal of Scientific & Engineering Research, vol. 5, no. 7, pp. 1178-1192, 2014.

R. Ratnawati and A. Salim, "Desain Ulang Alat Penukar Kalor Tipe Shell and Tube dengan Material Tube Carbon Stell dan Stainless Stell 304," Jurnal Teknik Mesin Univ. Muhammadiyah Metro, vol. 7, no. 1, pp. 74-80, 2018.

R. Ronquillo, "Understanding Heat Exchangers," 2019. [Online]. Available: https://www.thomasnet.com/artic-les/process-equipment/understanding-heatexc-hangers/. [Accessed 5 Oktober 2021].

P. A. Schweitzer, Fundamentals of Metallic Corrosion: Atmospheric and Media Corrosion of Metals Edisi 2, United Kingdom: Taylor & Francis, 2007.

A. A. Shrikant, R. Sivakumar and M. Vivekanandan, "Comparison of Shell and Tube Heat Exchanger using Theoretical Methods, HTRI, ASPEN and SOLIDWORKS simulation softwares. Int.," Journal of Engineering Research and Application, vol. 6, no. 3, pp. 99-107, 2016.

N. B. Sigimon, K. J. Jose and A. Surendran, "Thermal designing of shell & tube heat exchanger: a review.," Elixir Mech. Engg, vol. 78, no. 1, pp. 29563-29569, 2015.

N. S. Solke, A. Sur and M. Sapre, "Material selection and design of shell and tube heat exchanger for thermos-syphon steam generator.," in IOP Conf. Series: Materials Science and Engineering, India, 2020.

Tubular Exchanger Manufacturers Association (TEMA), T.E.M.A., tandards of the Tubular Exchanger Manufacturers Association Edisi 10, United States: Tubular Exchanger Manufacturers Association (TEMA), 2019.

T. Yasunaga, T. Noguchi, T. Morisaki and Y. Ikegami, "Basic Heat Exchanger Performance Evaluation Method on OTEC," Journal of Marine Science and Engineering, vol. 6, no. 32, pp. 1-12, 2018.

S. Yousufuddin, "Heat Transfer Enhancement of a Shell and Tube Heat Exchanger with Different Baffle Spacing Arrangements.," Scholar Journal of Applied Sciences and Research, vol. 1, no. 6, pp. 50-56, 2018.

DOI: http://dx.doi.org/10.30998/faktorexacta.v15i4.14148